Shop  |  Fabric Mojo  |  Info  |  Home   
Mountain Laurel Designs   
  Home » Catalog » TARPS » My Account  |  Cart Contents  |  Checkout   
PACKS (15)
TARPS (13)
Hammock Hexagon Tarp $155.00



Lightest Full Size Hex Hammock Tarp Available

10.5' Long X 8.5' Wide - Large Enough for Extra Long and Double Wide Hammocks

Cuben Fiber : 8.5oz $300 White or Light Green - Note Color Choice In Comments
Pro Silnylon : 16.5oz $155 Gray, Brown, OD Green or Yellow - Note Color Choice In Comments


• All tieouts include our new Linelocks for one-handed rapid adjustment and quick setup.
• See our Fabrics Mojo page for various fabric info.
• Six perimeter tieouts
• Three inside ridgeline hang points to connect bug nets or hang items.
• Reinforced tie outs.
• Catenary cut curves on the the ridge line and all sides for a tight pitch.
• Ridgeline tieouts with locking grommet holes for our CF poles or Trek poles for ground use mode.
• Cuben Fiber version has bonded and reinforced ridgeline seam - no stitching - no seam sealing needed


• Silnylon Stuff Sack
• Guyline
• 1.5oz Tube McNett Silnet seam sealer


Carbon Fiber Straight Poles
Super Stiff Premium Carbon Fiber Poles For Ground Use
• 28" Rear .9oz
• 42" Front 1.65oz
• .355 outside diameter Multi-Ply Multi Direction carbon fiber construction- not just a simple pultruded or wrapped tube in one direction like cheaper CF poles
• Grommet locking tips
• 15.5" long folded lengths for compactness
• Long aluminum internal ferrules with fast connect rounded end guides and tube spacer bumpers to prevent CF to CF abrasion
• The very best CF tarp pole avialable!

Stake Package

• Six 6.5� , .28oz each (8gm) Ti Stakes $25

Seam Sealing Instructions

How to a Seam Seal an MLD Pro Silnylon Shelter

(Cuben Fiber Shelters do not need seam sealing.)

1: Pitch and inspect your shelter for any issues. Once it is seam sealed it is non returnable except for significant defects.

2: Use the supplied SilNet and only the SilNet. (If you want to dilute it or use some other silicone sealant it should work OK and is common (research this yourself online) but your are on your own- results may vary and are not covered by warranty - if you go this route it is assumed you know 100% what you are doing and have done it before!!!)

3: Pitch the shelter tightly. Temps should be above 60 F and humidity below 80%. You may do this indoors. You may also do one seam at a time indoors if the seem is stretched slightly. Pinning one seam from each end on the floor between two heavy objects works OK.

4: We use the SilNet straight from the tube. Do not make a big hole in the sealer tube - start small so you can control flow. Multiple small application is a lot better than one big smear.

5: Main Seams: Place a small bead on the seam along the stitching. Work on a 3’- 4’ section at a time. Use a finger to press the sealer into the stitching and the small valley at the edge of the seam where it is rolled under.


NOTE: You only need to seal the OUTSIDE of the shelter ONLY. You do not need to seal the bottom perimeter roller edge stitching. It is OK to add a small bead on the leading edge of the triangle tieouts reinforcement stitching, but it is not required.

SPECIAL AREAS: Add a little sealer to any tieout stitching on the middle of a panel (Mids, Cricket and SuperTarps). Seal the zipper storm flap stitching and tieouts on the Mids. Seal the stitching and apex tieouts areas on the Mids, Crickets and TrailStars.

IMPORTANT: Do no go back and forth over the wet seam too much - after a minute or three it will get gummy and look bad. Better to wait 8 hrs and then OK to add some over any area you missed.

Available Options:
Fabric Type:
Straight Carbon Fibre Poles:
Shopping Cart more
0 items

Copyright © 2017 Mountain Laurel Designs
Powered by osCommerce InMotion Hosting